Exciting NEW Fabricated parts for the shop

[richb]

Hi Al whats the price on the vr6 mount kit really interested

[Al]

Is the vr6 mount kit specific to the vr6 or would it take any engine that would bolt straight into a mk3 golf or raddo?

It is specific to the VR6 type engines, so it will mount the 2.8 & 2.9 VR, 2.8 4mo & R32 engines so long as a 5 speed is used. But in theory yes you could use it except for 1 mount to mount any VW engine

sweet. did you get my email last week al?

TBH im a bit behind on my emails as I had a sh1t week down the workshop last week I will take a look, was an email or PM

Hi Al whats the price on the vr6 mount kit really interested

Will work it out in a minute once I have calculated what its cost to get them made

[Al]

This is the VR6 mounting Kit, it consists of 6 fabricated mounts, and 5 welded plates. the price of this kit reflects the time cost and money gone into producing them. £350 inc vat & delivery. Combine that with a cheap VR6 donor and you have yourselves a cheap VR6 MK1

fabricated parts


Parts that require welding in

[Al]

STAINLESS STEEL

MK1 short shifts

http://www.justcaddys.com/mk1-5-spee...ort-shift.html

3 positions to chose from

£32.95 inc vat & delivery

[richb]

vr6 kit looks smart. Stupid question but is the vr6 kit fairly self explanatory where those mounts go when you offer the engine up?

[worthingcaddy]

kit looks awesome al, i'm quite pleased with myself too because you've had it made exactly how i've fitted mine i'd say thats a bloody good price for the kit too, certainly alot easier to buy that kit than make your own from scracth (still cheating though haha)

[Al]

vr6 kit looks smart. Stupid question but is the vr6 kit fairly self explanatory where those mounts go when you offer the engine up?

These are the parts that need welding in

This mount is where the A/C pump would normally sit


And this is the drivers side rear mount, ignore the VR alloy mount in the picture as this is replaced by the mount in the above pictures

[Al]

kit looks awesome al, i'm quite pleased with myself too because you've had it made exactly how i've fitted mine i'd say thats a bloody good price for the kit too, certainly alot easier to buy that kit than make your own from scracth (still cheating though haha)

The kit is basically an updated and improved version of the Detlev kit that we used back in 2003 on B1GVR

[gander]

It was an email through your shop web site mate. I will have a vr6 mount kit but might need them welded in unless there is a easy how to and where to weld the mounts in. I couldn't find a phone number for you.

[jonboy]

any plans for down pipes?

[worthingcaddy]

i know, haha i'm just having a moan because i wish i had had a weld in kit when i did it. looks spot on Al i'm sure it will sell well tahts for sure

[richb]

As Gander said is there a how to and where to weld the mounts in? i was trying to work out where they go from pics.

[Al]

It was an email through your shop web site mate. I will have a vr6 mount kit but might need them welded in unless there is a easy how to and where to weld the mounts in. I couldn't find a phone number for you.

As Gander said is there a how to and where to weld the mounts in? i was trying to work out where they go from pics.

The welding is quite straight forward. The kit uses 5 mounts to mount the VR.

You would mount the engine first using 3 of the bolt in mounts, these are all on the gearbox end so will give you your position.

Then you would weld in the two mounts on the drivers side, buy supporting that end of the engine for the correct height.

On the drivers side chassis, the original 4 cylinder mount will need to be removed. Also the chassis leg will either need to be notched or beaten out the way to make clearance for the block.









Gander I will PM you

Al

[Al]

any plans for down pipes?

Not at the moment Jon, whilst the welder is out its not to much of a drama fabricating the down pipes

[Al]

Also to use this kit you will need 3 rubber mounts

1x MK1 Rubber mount (under battery tray) http://www.justcaddys.com/gearbox_mo...pper_left.html

2x MK2/3 Rear gearbox/mount bush



you will already have one of these if you have a complete donor vehicle. I can supply these as well if needed

[freestyle72]

MK3 TDI mounts would be amazing.
AHU engine.

Got anything that works?

[43655]

MK3 TDI mounts would be amazing.
AHU engine.

Got anything that works?

all you need is 5-speed gearbox mounts and cut down the standard 1.6D engine mount apparently. Still waiting for Ultraviolent to send me the mounts to mock up my engine but the mounts on the body stay right where they are

[freestyle72]

Just as a second question would the 1.8t mounting kit then work fo the alh engine since theyare both mk4?

[jpskate8]

02A & 02J Gearbox Mount.
http://www.justcaddys.com/02a-and-02...ox-mounts.html

Anyone ever use these? Im having an issue installing the rear on this kit.

I cant seem to reach my rear mount with this bracket?


Pictures of this installed if anyone has used these mounts...

thanks
Josh

This is the VR6 mounting Kit, it consists of 6 fabricated mounts, and 5 welded plates. the price of this kit reflects the time cost and money gone into producing them. £350 inc vat & delivery. Combine that with a cheap VR6 donor and you have yourselves a cheap VR6 MK1

fabricated parts


Parts that require welding in

[trev0006]

What year is your vehicle?

02A & 02J Gearbox Mount.
http://www.justcaddys.com/02a-and-02...ox-mounts.htmlgoodyears4

Anyone ever use these? Im having an issue installing the rear on this kit.

I cant seem to reach my rear mount with this bracket?


Pictures of this installed if anyone has used these mounts...
http://www.dpccars.com/photos-13/01-...orvette-C7.htm
thanks
Josh