Search Articles


by macetheace Published on 24-06-2009 12:01 AM
Thought I'd finally put this all together. Al can you move to "how to section" You'll need - 2 pairs of rear lights Drill Small cutting disc (like a dremel) Heat Gun Clear silicone
by sitrials Published on 20-10-2008 02:19 AM
Time: 1 week (approx 24hrs) Tools Required: MIG Welder Spanners, Sockets, Ratchets 90Degree Angle Clamps (x4 preferably) Angle Grinder (cutting discs and flap wheels) Hack Saw Mitre Saw
by pre67 Published on 05-08-2008 11:42 PM
converting a gti injection head to run carbs right this is a 1.8 gti head this is haw you block of the injectors start buy removing the the brass inserts with a large allen key ones removed all the brass inserts then remove all the red plastic bits held down by the brass inserts ...
by Mk1 Published on 01-05-2008 10:47 PM
Right, I did this a little while ago and only just got around to writing it up. Tools and equipment; 2 Porsche seats 2 Mk1/2 VW Subframes for Cobra Bucket seats (mine were Demon Tweeks 07927 handed) 5mm Allan key 10 and 13mm spanner Drill with 2 and 5mm drill bits A pair of pliers and a.....
by pre67 Published on 13-12-2007 12:31 AM
Here's what where gonna use to get rid of all that rust - cheap vinega:p Cheap parts washer! 32ltr container cost £2.99 at a local hardware store. Then, place the rusted parts in the container. Cover with plenty of vinegar and leave to soak overnight. Scrub with a plastic or wire brush.
by Tiz Published on 15-08-2007 09:29 PM
Right, to my knowledge one of these has always been asked for but never done. Sepia kid just asked me to make a quick guide for him so i thought i would write this up for everybody. It was about 6 months ago when i did this but to my knowledge i have listed all the information needed below. If...
by Al Published on 11-02-2007 07:31 PM
AT YOUR OWN RISK… will take no responsibility in your workmanship. If you are in doubt then get a professional to do this work for you. Even better get me to do it ;) This how to, will presume you are competent with spanners and can weld or have somebody on hand to do the...
by P4ulo Published on 12-10-2006 09:43 PM
Here is the long promised wheel polishing guide. (P4ulo-inc. accept no responsibility for any serious damage to wheels, fingers, eyes and machinery used in this guide!!) Right. First of all, (stating the obvious) you need to have some alloy wheels. You cannot do this process to steel wheels....
by Al Published on 23-04-2005 06:06 PM
This installation uses your original (OEM) window regulators, and the motors from any VW from the "Caddy" era. It took me about an hour to suss out the first regulator, the second one took less than 10 minutes. All pics are of the UK passenger mechanism. 1. Drill out the 4 rivets h...
by Al Published on 23-06-2004 09:51 PM
Not so much a "How To" but more of an insight to bigger brakes that can be modified to fit your Caddy's Front 239mm for use with 13" + wheel rims This is the Std factory Caddy front disc size in NON vented guise, to make them more efficient you can fit MK1 GTi vented discs a...
by Al Published on 18-06-2004 05:52 PM
Note: This topic is based on installing height adjustable leather seats from a 1997 VR6 Golf 3 Door into your Caddy, although all other MK3 seats will be a similar operation to fit. I WILL NOT be going into detail on removing & fitting the seats from your vehicle, frankly if you need...
by Al Published on 14-05-2004 09:42 PM
Submitted by "Kevlar" as taken from the "The Golf Magazine" May 2003
by Al Published on 21-08-2003 07:06 AM
Submitted by Admin This is a question which pops up often on a lot of VW forums, so I thought I would try to put something into black and white for all to see:) First off, what I am about to say is based on the European spec Caddy as I am not familier with the US built truck, although the...
Page 2 of 2 FirstFirst 1 2

Most Read Articles

Most Commented Articles

Top Authors

Article Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order articles in...

Note: when sorting by date, 'descending order' will show the newest results first.

Article Forum v4.1.2 Copyright by BananaLive