Activity Stream

Filter
Sort By Time Show
Recent Recent Popular Popular Anytime Anytime Last 24 Hours Last 24 Hours Last 7 Days Last 7 Days Last 30 Days Last 30 Days All All Photos Photos Forum Forums Articles Articles
Filter by: Last 24 Hours Clear All
  • Sammo's Avatar
    Today, 11:58 AM
    Just a quick update to say I haven't given up on the van, however I have lost every ounce of motivation to work on it at the moment! I'm hoping to...
    89 replies | 3772 view(s)
  • fuus's Avatar
    Today, 09:43 AM
    fuus replied to a thread Brakes won't bleed :( in Brakes
    Following the advice given here, I place a fresh piece of kitchen towel under the compensator overnight to see if it was leaking as I couldn't see...
    8 replies | 83 view(s)
  • lumberjack23's Avatar
    Yesterday, 10:04 PM
    got the revised 3D print prototype back and the fit is alot better, the hex bolts will be shorter to be unseen in the recess, so now it can finally...
    109 replies | 5418 view(s)
  • fuus's Avatar
    Yesterday, 10:00 PM
    fuus replied to a thread Brakes won't bleed :( in Brakes
    Really do not want to be forking out for a compensator, so fingers crossed it isn't that...
    8 replies | 83 view(s)
  • Al's Avatar
    Yesterday, 09:46 PM
    Al replied to a thread Brakes won't bleed :( in Brakes
    compensator is probably fucked. Had the same issue a few times. disconnect the pipe from the wheel cylinder and pump the pedal, if it just...
    8 replies | 83 view(s)
  • fuus's Avatar
    Yesterday, 09:34 PM
    fuus replied to a thread Brakes won't bleed :( in Brakes
    Will report back tomorrow how I've got it plumbed up for sure Up until this point I've been pedal bleeding, but might have a go with a pressure...
    8 replies | 83 view(s)
  • swainy's Avatar
    Yesterday, 09:04 PM
    swainy replied to a thread Brakes won't bleed :( in Brakes
    My input/output was top and bottom. Can't remember which way round though.
    8 replies | 83 view(s)
  • mitty85's Avatar
    Yesterday, 08:54 PM
    Rob came to see me tonight at work with 4 lengths of 12mm stainless bar. I’m too tight to buy new extended U bolts so we made our own. I threaded...
    19 replies | 430 view(s)
  • ScotClayShooter's Avatar
    Yesterday, 08:51 PM
    I had that issue with my rear drivers side,It was a fault in the compensator With the pressure bleeder and pushing the pedal i could just about...
    8 replies | 83 view(s)
  • fuus's Avatar
    Yesterday, 08:42 PM
    fuus replied to a thread Brakes won't bleed :( in Brakes
    It does have the compensator, which I'm pretty sure is plumbed up right. The inputs are on the right hand side, and the outputs on the left?
    8 replies | 83 view(s)
  • swainy's Avatar
    Yesterday, 08:24 PM
    swainy replied to a thread Brakes won't bleed :( in Brakes
    You got pipes correct on the compensator if it has one? I had the same on my van, swapped pipes in compensator and bled up fine.
    8 replies | 83 view(s)
  • fuus's Avatar
    Yesterday, 07:24 PM
    fuus started a thread Brakes won't bleed :( in Brakes
    :bh Been fiddling with it for a couple of days now and I just can't get the brakes to bleed. Any suggestions gang? 3/4 brakes bleed absolutely...
    8 replies | 83 view(s)
  • Cadby's Avatar
    Yesterday, 12:43 PM
    Very few Caddys at the Show, a few MK1 Golfs, but had a great time from the Friday at noon till Sunday. There were some cracking vehicles at the...
    4 replies | 152 view(s)
No More Results