Activity Stream - VW Caddy (AKA VW Rabbit Pickup) Forum

Sort By	Time	Show
Recent Recent Popular Popular	Anytime Anytime Last 24 Hours Last 24 Hours Last 7 Days Last 7 Days Last 30 Days Last 30 Days	All All Photos Photos Forum Forums Articles Articles

Today, 10:04 PM

lumberjack23 replied to a thread Work so far in Caddy Build Projects

got the revised 3D print prototype back and the fit is alot better, the hex bolts will be shorter to be unseen in the recess, so now it can finally...

109 replies | 5338 view(s)

Today, 10:00 PM

fuus replied to a thread Brakes won't bleed :( in Brakes

Really do not want to be forking out for a compensator, so fingers crossed it isn't that...

7 replies | 42 view(s)

Today, 09:46 PM

Al replied to a thread Brakes won't bleed :( in Brakes

compensator is probably fucked. Had the same issue a few times. disconnect the pipe from the wheel cylinder and pump the pedal, if it just...

7 replies | 42 view(s)

Today, 09:34 PM

fuus replied to a thread Brakes won't bleed :( in Brakes

Will report back tomorrow how I've got it plumbed up for sure Up until this point I've been pedal bleeding, but might have a go with a pressure...

7 replies | 42 view(s)

Today, 09:04 PM

swainy replied to a thread Brakes won't bleed :( in Brakes

My input/output was top and bottom. Can't remember which way round though.

7 replies | 42 view(s)

Today, 08:54 PM

mitty85 replied to a thread It’s only supposed to be a parts van for the project van in Caddy Build Projects

Rob came to see me tonight at work with 4 lengths of 12mm stainless bar. I’m too tight to buy new extended U bolts so we made our own. I threaded...

19 replies | 404 view(s)

Today, 08:51 PM

ScotClayShooter replied to a thread Brakes won't bleed :( in Brakes

I had that issue with my rear drivers side,It was a fault in the compensator With the pressure bleeder and pushing the pedal i could just about...

7 replies | 42 view(s)

Today, 08:42 PM

fuus replied to a thread Brakes won't bleed :( in Brakes

It does have the compensator, which I'm pretty sure is plumbed up right. The inputs are on the right hand side, and the outputs on the left?

7 replies | 42 view(s)

Today, 08:24 PM

swainy replied to a thread Brakes won't bleed :( in Brakes

You got pipes correct on the compensator if it has one? I had the same on my van, swapped pipes in compensator and bled up fine.

7 replies | 42 view(s)

Today, 07:24 PM

fuus started a thread Brakes won't bleed :( in Brakes

:bh Been fiddling with it for a couple of days now and I just can't get the brakes to bleed. Any suggestions gang? 3/4 brakes bleed absolutely...

7 replies | 42 view(s)

Today, 12:43 PM

Cadby replied to a thread Volksweald Show. Penshurst. Kent. in Shows, Meets, and Events in the (UK)

Very few Caddys at the Show, a few MK1 Golfs, but had a great time from the Friday at noon till Sunday. There were some cracking vehicles at the...

4 replies | 145 view(s)

Yesterday, 11:32 PM

g60smol started a thread Chrome front bumper in Mk1/A1 Caddy

Hi guys I’m in need of a couple of measurements from a chrome or steel front bumper, what I need is how far out from the front panel the back edge of...

0 replies | 35 view(s)

Yesterday, 10:48 PM

Mike.F replied to a thread Work so far in Caddy Build Projects

looking good mate, I was discussing the same thing last night about how much to build it back up and after we went through everything it was agreed...

109 replies | 5338 view(s)

Yesterday, 09:22 PM

swainy replied to a thread Swainys Mk2 caddy van no2 in Caddy Build Projects

I know. I did hit a rather large hump in the road, travelling rather quickly so must have just been the sharp shock from that. The new ones look...

173 replies | 17552 view(s)

Yesterday, 08:48 PM

lumberjack23 replied to a thread Swainys Mk2 caddy van no2 in Caddy Build Projects

Dont think ive ever seen a rose joint un-peel itself!

173 replies | 17552 view(s)

Yesterday, 08:44 PM

ScotClayShooter replied to a thread Swainys Mk2 caddy van no2 in Caddy Build Projects

I thought corrosion was going to be the issue with the rose joints not breaking Rob!

173 replies | 17552 view(s)

Yesterday, 08:25 PM

lumberjack23 replied to a thread Work so far in Caddy Build Projects

sooooo having a break from the welding and been building it back up and wondering how far to build the car back up before i strip it down for the...

109 replies | 5338 view(s)

Yesterday, 07:31 PM

swainy replied to a thread Swainys Mk2 caddy van no2 in Caddy Build Projects

Rear suspensions been working pretty well. Apart from the rose joint that broke last week. It moved the axle back and has worn through the rear...

173 replies | 17552 view(s)

Yesterday, 06:03 PM

GypsyR replied to a thread Front end replacemnt in Bodywork and Related Trim

Collision shops seem to like just in front of the shock towers generally. I'm guessing because that way they mostly stay out of the structural...

1 replies | 112 view(s)

Yesterday, 05:50 PM

GypsyR started a thread Time for new dash speakers-MK1 in ICE (In Car Entertainment)

The ones it came with were trashed. Now one of the badly fitting ones I put in it quit. So I'm looking for new ones. I've no interest in hi-fi, just...

0 replies | 27 view(s)

Yesterday, 04:19 PM

Slacker The Pinstripet replied to a thread Breaking Seat Inca in Parts and Accesories For Sale

Full van pretty much, seats have gone and starter motor and rear lock are taken. It’s getting weighed in on Saturday. Txt me on 07708268830 for...

12 replies | 738 view(s)